Spring Return Electric Actuators

ICI‘s spring return electric actuators were designed for systems using quarter turn valves and dampers requiring protection against catastrophic system failure upon loss of electricity resulting in costly loss of process media and lost production. Our spring return actuators are available in four sizes with a maximum spring end torque of 1000 lb × in torque. These heavy-duty spring return actuators are manufactured for fail-safe applications only and are not intended for use on control applications. These machines are equipped with hardened steel spur gear drive train guaranteeing high efficiency, quiet operation and long trouble free life.

The heavy-duty sand-cast aluminum enclosure meets NEMA 4 specifications and has a thermally bonded ultraviolet resistant polyester powder coating that not only enhances its appearance but also is a tough corrosion resistant coating.

ES2
AS4
AS6
AS10

SPECIFICATIONS:

Output Torque 200 Ln-In (22.6 Nm)
Cycle Time 10 sec/90° rotation model ES2
Duty Cycle 10% model ES2,
Motor 115Vac-50/60Hz-1Ph.
Mode of Operation Power open and close, spring to function only upon loss of main power supply.

OPTIONAL VOLTAGES:
230Vac-50/60Hz-1Ph.with thermal overload protection.

Lock Rotor Current 115Vac. = .75 Amps.
230Vac. = .38 Amps.

Enclosure
NEMA 4 Standard
Sand-cast aluminum with 300 series stainless steel fasteners and thermally bonded polyester powder coating.

OPTIONAL ENCLOSURES:
NEMA 4X & NEMA 7

Output Drive
ISO 5211 F07 (17mm female star) model ES2

Mounting Universal, ISO 5211 F07
Manual Over Ride Consult factory
Lubrication Permanent
Temperature -40° F to +140° F (heater required at 0° F. and below).
Weight 15 Lbs.
Switches 16 A. 125/250VAC

AVAILABLE OPTIONS: Extended duty (75% model ES2) motor, maximum of 4 auxiliary switches, declutching manual over ride with hand wheel, NEMA 7 enclosure, feedback potentiometer, 4-20mA position transmitter (requires 24Vdc power supply), compartment heater, heater and thermostat, breather, light indication, two wire control, remote/off/local control panel, and one additional conduit entry.

Model ES2 Electric Actuator

Model ES2 is a light duty actuator designed for fail-safe applications. For best life expectancy it is recommended that model ES2 be powered in both clockwise (CW) and counter clockwise (CCW) directions. If used in this manner one can expect over 2,000 open/close cycles. When allowed to spring to the fail position as the normal model of operation the life of the actuator is severly shortened. ES2 has a spring end torque of 200 in·lb with a closing speed of 3 sec./90° upon loss of power. This actuator is ideally suited for ball valves and dampers with torque ratings of up to 145 in·lb.

Standard equipment includes 115Vac-1ph 25% duty cycle motor with thermal over load protection, set to fail closed (CW rotation) upon loss of power, two limit switches, power on brake, stainless steel fasteners, 300 series stainless steel output drive, polyester powder coating.

SPECIFICATIONS:
Output Torque 400 Lb-In (45.2 Nm)
Cycle Time 12 sec/90°
Duty Cycle 25%
Motor 115Vac-50/60Hz-1Ph.

OPTIONAL VOLTAGES:
230Vac-50/60Hz-1Ph.with thermal overload protection.

Lock Rotor Current 115Vac. = 2.99 Amps.
230Vac. = 2.74 Amps.

Enclosure
NEMA 4 Standard
Sand-cast aluminum with 300 series stainless steel fasteners and thermally bonded polyester powder coating.

OPTIONAL ENCLOSURES:
NEMA 4X & NEMA 7

Output Drive
ISO 5211 F07 (17 mm male square)

AVAILABLE OPTIONS: Extended duty motor, maximum of 4 auxiliary switches, declutching manual over ride with hand wheel, NEMA 7 enclosure, feedback potentiometer, 4-20mA position transmitter (requires 24Vdc power supply), compartment heater, heater and thermostat, breather, light indication, two wire control, remote/off/local control panel, and one additional conduit entry.

MODEL AS4 Electric Actuator

Model AS4 spring return electric actuator is a robust heavy-duty actuator recommended for systems requiring as many as 74 cycles per day (approximately 27,000 annually). Like model ES2 the operating cycle life of the actuator is drastically affected by the model of operation, power to open and close will provide for years of reliable performance. AS4 has a spring end torque of 400 lb·in with a closing speed of 3 sec./90 degrees upon loss of power. This actuator is ideally suited for ball valves and dampers with torque ratings of up to 300 lb·in.

Standard equipment includes 115Vac-1ph Ccontinuous duty motor with thermal over load protection, set to fail closed (CW rotation) upon loss of power, two limit switches, power on brake, stainless steel fasteners, 300 series stainless steel output drive, polyester powder coating.

SPECIFICATIONS:

Output Torque 600 Ln-In (67.8 Nm)
Cycle Time 12 sec/90 °
Duty Cycle 25%
Motor 115Vac-50/60Hz-1Ph.

OPTIONAL VOLTAGES:
230Vac-50/60Hz-1Ph.with thermal overload protection.

Lock Rotor Current 115Vac. = 2.99 Amps.
230Vac. = 2.74 Amps.

Enclosure
NEMA 4 Standard
Sand-cast aluminum with 300 series stainless steel fasteners and thermally bonded polyester powder coating.

OPTIONAL ENCLOSURES:
NEMA 4X & NEMA 7

Output Drive
ISO 5211 F07 (17 mm male square)

MODEL AS6

Model AS6 electric spring return actuator is a robust heavy-duty actuator recommended for systems requiring as many as 74 cycles per day (27,000 anually). AS6 has a spring end torque of 600 lb·in with a closing speed of 3 sec./90 degrees upon loss of power. this actuator is ideallysuited for ball valves and dampers with torque ratings of up to 440 lb·in.

SPECIFICATIONS:

Output Torque 1000 Lb-In (113 Nm)
Cycle Time 14 sec/90°
Duty Cycle continuous
Motor 115Vac-50/60Hz-1Ph.

OPTIONAL VOLTAGES:
230Vac-50/60Hz-1Ph.with thermal overload protection.

Lock Rotor Current 115Vac. = 2.99 Amps.
230Vac. = 2.74 Amps.

Enclosure
NEMA 4 Standard
Sand-cast aluminum with 300 series stainless steel fasteners and thermally bonded polyester powder coating.

OPTIONAL ENCLOSURES:
NEMA 4X & NEMA 7

Output Drive
1” square male shaft model AS10

Mounting Universal, ISO F10
Manual Over Ride Consult factory
Lubrication Permanent
Temperature -40° F to +140° F (heater required at 0° F. and below).
Weight 70Lbs.
Switches 16 A. 125/250VAC

MODEL AS10

Model AS10 electric spring return actuator is a robust heavy-duty actuator recommended for systems requiring as many as 18 cycles per day (approximately 6500 annually). AS10 has a spring end torque of 1000 lb·in with a closing speed of 3 sec./90 degrees upon loss of power. This actuator is ideally suited for ball valves and dampers with torque ratings of up to 775 lb·in.